AutoDyn 11 Chassis Dyno
600+ hp (447kW) and 150 mph (241 kph)
SuperFlow's AutoDyn 11 is a compact cradle-roll chassis dynamometer
with an eddy current power absorption unit. The cradle-roll design
makes it easy to load and unload vehicles. The AutoDyn 11 fits in
shallow pits or above ground with a ramp kit. It is very affordable
and yet has all the data acquisition and control power of
SuperFlow's premium models.
The AutoDyn 11 allows you to test vehicles with over 1,100
horsepower at speeds up to 150 mph. Its standard power absorption
unit holds up to 750 hp at the tire patch. The AutoDyn 11's rolls
are only 23" (58 cm) apart so you can test narrow-track drag race
Its 7,700 lbs (3500 kg) per axle test capacity and generous 97"
outer roll width allow you to test large vehicles. Its durable
construction, 10-year bearings and first rate customer service
department help make the AutoDyn 11 a low-cost, long term
- Test capacity over 1,100 hp and up to 150 mph; * 750 hp peak
- 10.7" diameter cradle rollset with pneumatic vehicle lift
and integrated roll brake makes it fast and easy to load and
- Compact design saves valuable floor space whether mounted in
the floor or above-ground
- Standard eddy current power absorption unit, load cell, and
software allow you to run built-in and configurable loaded tests
- WinDyn™ dynamometer software makes it easy to configure,
run, save, and analyze dynamometer tests
- Built-in weather station (air temperature, barometric
pressure, and humidity)
- Inductive ignition sensor clip (user adjustable gain)
- Handheld remote provides complete control of the test
- Side travel restrictors help keep the tires in the cradle
and accelerate loading procedures
- 76 data acquisition input channels
- Shop banners and decal kit, Web site listing
- One year warranty, including parts and labor**
* Cold, intermittent rating. Test up to 130 mph (210 kph)
** Does not include travel costs, travel time, and expenses.
||10.7" (27.2 cm)
||1,100 HP (1,864 kW)
|Peak Absorbed Power
||750 HP (559 kW)
||150 mph (241 km/h)
||23" inside - 97" outside (58 cm - 246
|Base System Inertia
||770lbs. (349 kg)
||7,700 lbs. (3,493 kg)
||50-100 psi (345 - 690 kPa)
||110 VAC / 15A or 250 VAC / 8A and
208-250 VAC / 20 A
|Shipping Weight (approximate)
||4,000 lbs. (1,814 kg)
SuperFlow offers lightweight aluminum ramp kits for the
AutoDyn 11 and AutoDyn 30 chassis dynos. Kits include
heavy-duty aluminum ramps and extended platforms that
support the vehicle during testing. Because they are
light-weight these ramps work great for portable dyno
applications and they are easy to move in and out of place.
Ramps are perfect if you are unable to install your
SuperFlow chassis dyno in a pit or when shop space is
limited because they stack neatly out of the way when not in
use. Contact a SuperFlow Sales Engineer today to get the
correct ramp kit for your chassis dynamometer.
SuperFlow offers several different 4-post hoists to fit any
needs and budget. Models are available with a walking
platform, safety rails and access ladders to make working on
vehicles easy and safe. SuperFlow also offers an economy
hoist that does not include the extra features listed above,
but still works great for loading vehicles on and off your
chassis dyno quickly and easily.
All lifts come with tie-down anchor points at the front and
rear of the platform to secure vehicles for testing. 4-post
hoists let you make performance upgrades anywhere on the
vehicle without having to move it from the dyno. Additional
benefits include oil changes, performance upgrades, brakes,
tire rotations, etc.
Contact a SuperFlow Sales Engineer today to learn more about
4-post hoists as well as other options for above ground
installation of your SuperFlow chassis dyno.
|AutoDyn Tie Down
Standard tie-down strap kits include (4), 2in. by 15ft.
heavy duty straps with ratchets and (2), 2in. by 4ft.
web-sling straps with eyelet to eyelet ends. Cored in-floor
anchors are available separately.
In-Floor AnchorsSuperFlow offers in-floor, compression style
anchors to outfit your shop with convenient, yet out of the
way tie down points. The 3.5in. anchors feature a chain
receiver that allows you to quickly attach the tie down
chain or remove it when not in use. The anchors have a
10,000 lb. (4,536kg) horizontal rating and a 500 lb. (227
kg) vertical rating. A cover plate is included to fill the
receiver hole when the anchors are not being used.
*Chain is not included because each installation varies
SuperFlow’s optical wheel tachometer reads wheel speed using
an infrared beam and reflective tape. It features a magnetic
base for secure mounting to any AutoDyn frame. The optical
tach is non-contact and works in many applications where
inductive pickups may not. Contact a SuperFlow Sales
Engineer today for more information on all of the options
available for SuperFlow chassis dynamometers.
SuperFlow’s Inductive Spark Pick-Up Assembly features a
rugged housing that protects the device from tough shop
environments and allows it to provide years of service. With
user-adjustable sensitivity you’re able to dial in the
device exactly how you want it.
The spark pick-up includes one inductive clip. For wasted
spark ignition systems a second clip can be added. Contact
SuperFlow today for more information on this and other
options to get the most out of your SuperFlow chassis dyno.
The SuperFlow sensor box is easily upgradeable at any time.
Several pressure sensor expansion kits are available that
provide up to 10 additional pressures per expansion panel
for fluid or gas pressures. Monitor oil, manifold, fuel
system, air inlet, exhaust and auxiliary pressures. View all
of the data live in our WinDyn software and also save it for
easy post test graphing and analysis.
- Oil Pressure 150 psi
- Manifold Pressure: 200 in Hg
- Fuel Pressure: 150 psi
- Air Inlet Pressure ± 140 in. Hg
- Exhaust Pressure: ± 140 in. H2O
- Auxiliary Pressures also available
- Metal transducers (for hydrocarbon
- PCB-mount transducers (for non-hydrocarbon
- 0-5 psi
- 0-150 psi
- 0-150 psi
- Differential pressure transducers
- ± 5 psi
- ± 30 psi
- ± 100 psi
- Different ranges can be set by the
- Remote systems available for high pressures
- 0-150 psi
- 0-300 psi
- 0-2,000 psi
- *Requires Analog Input Expansion Panel
Sensor Expansion Kits
Expand your sensor box with a 16-channel thermocouple panel
for Type K, Type J or Type T thermocouples. Monitor oil and
water temperatures live in our WinDyn software then save the
data for easy post test graphing and analysis. Monitoring
temperatures is critical to accurate and repeatable testing
so SuperFlow offers several kits to suit any needs and
budget. Panels accept pole or spade thermocouple plug ends.
Contact SuperFlow today for more information on Temperature
Expansion Panels for your SuperFlow chassis dynamometer.
Oil Dip Stick sensorSuperFlow's oil dipstick temperature
probe plugs directly into the temperature expansion panel so
you can get accurate oil temperature readings with every
test. It includes a 10in. extension cable and features a
temperature range of -67° F to 1,200° F (-55° C to 704° C).
It is also available with an analog output to plug directly
into the interconnect panel or analog panel. This version
has a temperature range of -67° F to 257° F (-55° C to 125°
SuperFlow offers 8-channel analog voltage input panels so
customers can easily integrate data from exhaust gas
analyzers, lambda sensors, O2 sensors, and other emissions
monitoring equipment with our WinDyn software. You can then
monitor the data live during each test, and also save it for
post test graphing and analysis to see the data graphed over
the entire run. The panels can be configured with any
combination of the following ranges:
- 0-1 V
- 0-5 V
- 0-10 V
- 0-20 V
- 0-30 V
SuperFlow’s Battery Voltage Input Cable allows you to
monitor battery voltage live in our WinDyn software with the
0-20 VDC input. *Requires analog input expansion panel.
SuperFlow offers 4in. (10.2cm), 6in. (15.2cm), and 9in.
(22.9 cm), air flow measurement turbines. They are available
on their own or in a kit that includes a ceiling adapter,
flexible hose and carburetor adapter. The turbines have CFM
ranges as follows:
- 4in: 4 – 150 CFM (2 – 70 lps)
- 6in: 10 – 800 CFM (5 – 380 lps)
- 9in: 20 – 1,200 CFM (9 – 560 lps)
Adapters are available to adapt the 9” (22.9cm) air turbine
to Holley and Dominator carburetors.
SuperFlow fuel turbines come in three different ranges:
- Low flow: 0.3 – 30 GPH (1.13 – 113 l/h)
- Standard flow: 6 – 60 GPH (22.7 – 227 l/h)
- High flow: 28 – 140 GPH (106 – 530 l/h)
ODB-II Interface ModuleWith SuperFlow’s OBD-II Interface
Module you can easily monitor and record any OBD-II data
that the ECM makes available directly in our WinDyn
dynamometer software. The device plugs directly into the OBD-II
port and automatically shows you the available PIDs for that
vehicle. You can then quickly configure the system to
display the channels that you want to monitor live on
custom, user-defined WinDyn screens. With SuperFlow’s high
speed data acquisition you can close-loop control to OBD-II
channels and save any of them you want for post test
analysis and graphing.
With the OBD-II Interface Module you’re also able to read
Diagnostic Trouble Codes (DTC’s) and clear them once they
are resolved. Contact a SuperFlow Sales Engineer today for
more information on the OBD-II Interface Module for your
SuperFlow chassis dyno.
Air/Fuel SensorSuperFlow offers several lambda packages for
measuring air/fuel ratios. These packages integrate with our
WinDyn dynamometer software for live monitoring and easy
post test graphing and analysis. Contact a SuperFlow Sales
Engineer today to learn more about the available options so
you can get the most out of your SuperFlow chassis dyno.
Tailpipe Air Fuel ProbesWith SuperFlow exhaust probes you
can measure air/fuel data directly from the tailpipe.
Tailpipe probes integrate with our WinDyn dynamometer
software for live monitoring and easy post test graphing and
analysis. Contact a SuperFlow Sales Engineer today to learn
more about the available exhaust probes for your chassis
6500 Smoke AnalyzerSuperFlow’s Diesel Exhaust Opacity Meter
measures the opacity of visible smoke coming from the
exhaust. It’s rugged and portable design provides years of
easy use. Contact SuperFlow today for more information on
this and all the available options for your SuperFlow
Blow-by SensorSuperFlow’s blow-by sensors measures the
volumetric flow of crankcase blow-by. Two sizes are
available: 0.4 to 16 ACFM and .25 to 10 ACFM. Users have the
option to choose either an analog or frequency output.
Contact a SuperFlow Sales Engineer today for more
Driver's Trace SoftwareSuperFlow’s Driver’s Trace Software
integrates seamlessly with your SuperFlow chassis
dynamometer and allows drivers to follow a real-time moving
driver’s trace on it’s easy-to-read display. It can run any
.csv based drive cycle and it is easy to configure. Special
operations like shift points or display messages for the
driver can be included in the trace so each test is accurate
and repeatable. Contact a SuperFlow Sales Engineer today for
more information on our Drivers Trace Software for you
*Requires WinDyn 2.7 or higher.
Are you trying to inquire about a part
or check availability of a product or a solution service?
Please either call +60-3-7785 1255 at or email us at
or submit an enquiry form